Substantiation of efficiency of use of carbon

Authors

  • В.І. Бондаренко Національний технічний університет «Дніпровська політехніка», Дніпро, Україна Author
  • І.А. Ковалевська Національний технічний університет «Дніпровська політехніка», Дніпро, Україна Author
  • Г.А. Симанович Національний технічний університет «Дніпровська політехніка», Дніпро, Україна Author
  • Є.С. Цівка Національний технічний університет «Дніпровська політехніка», Дніпро, Україна Author
  • І.В. Шека Національний технічний університет «Дніпровська політехніка», Дніпро, Україна Author

DOI:

https://doi.org/10.33271/crpnmu/68.030

Keywords:

stress-strain state, carbon fiber, composite support, physical and mechanical properties, mine workings

Abstract

Purpose. To analyze the possibility of using support made of composite materials and evaluate its prospects for mine workings in coal mines. Conduct a comparative analysis of the physical and mechanical properties of carbon fiber and metal support, as well as compare their features. Determine the possibility of using a new composite lining for mine workings in the conditions of mines in the Western Donbas. Research methodology. An analysis of fastening materials was carried out and a general assessment was obtained, thanks to the physical and mechanical properties. An analysis of the stress-strain state of the possible use of an arched composite fastening of a circular cross section was carried out and the expediency of its use for a fastening system in difficult mining and geological conditions was determined. Research results. A detailed comparative analysis of the stress-strain state of a layered mass after the passage of a mine working was carried out using a new material in the fastening system. As a result of the study, it was concluded that in order to solve the problem of uneven distribution of rock pressure around the working, it is better to use a new composite fastening. The advantages and disadvantages of the innovative lining for the mine workings of coal mines in the Western Donbas are assessed. A limiting factor has been identified that today has a negative impact on the widespread use of this material, namely the high cost of carbon fibers. It was concluded that when using a composite lining of a circular cross section, it is possible to achieve an increase in the rate of workings, a decrease in the labor intensity of work and an improvement in the working conditions of miners in difficult mining and geological conditions. Scientific novelty. The regularities of the stress-strain state of a layered massif with an arched composite lining are determined in relation to the possible use of working support in zones of uneven distribution of rock pressure. Practical value. According to the results of the study, it was found that when using an arched composite lining, it is possible to achieve an increase in productivity, ensure the reliability of support for the goaf and improve the working conditions of miners.

References

Tkach,S.M., & Gavrilov,V.L. (2019).On regularities in coal industry development. Problemy nedropol'zovaniâ , (3)

Powering Past Coal Alliance: 20 countries sign up to phase out coal power by 2030. , (November 17, 2018). ABC News

Jewell, J., Vinichenko, V., Nacke L. etal. (2019). Prospects for power in gpast coal. Nature Climate Change , (9)

Timofeev, O.A., Sharipov, F.F., & Petrenko, B.V. (2021). COVID-19 pandemic impacton China's coalmarket. Ugol' , (1), 63-67. https://doi.org/10.18796/0041-5790-2021-1-63-673

Про схвалення Енергетичної стратегії України на період до 2035 року «Безпека, енергоефективність, конкурентоспроможність (2017).Постанова Кабінету Міністрів України від 18 серпня 2017 р. №605

Бондаренко, В.И., Ковалевская, И.А., Симанович, Г.А., & Черватюк,В.Г. (2012). Геомеханика нагружения крепиочистных и подготовительныхвыработок в слоистоммассивеслабыхпород . ЛізуновПрес

Бондаренко, В.И., Ковалевская, И.А., Симанович, Г.А., Барабаш, М.В., & Гусев, А.С. (2015). Взаимодействие грузонесущих элементов крепежной системы выемочных выработок «масcив – рама – анкер» . Літограф

Уголь в Украине http://energetika.in.ua/ru/books/book-1/part-2/section-7/7-7

Coal industry across Europe , 7th edition. https://euracoal.eu/info/coal-industry-across-europe/

Дрибан, В.А. (2000). Механизм деформирования массива горных пород вокруг выработок . Проблеми гірського тиску , (4), 172-182

Забигайло, В.Е., Лукинов, В.В., Пимоненко, Л.И., & Сахневич, Н.В. (1994). Тектоника и горно-геологические условия разработки угольных месторождений Донбасса . Наукова думка

Янко, С.В. (1993). Повышение эффективности работы угольных шахт Украины . Технпса

Composite materials (n.d.). https://compositesuk.co.uk/composite-materials/introduction

Goncharov, A. A., Dub, S. N., Agulov, A. V., & Petukhov, V. V. (2015). Structure, composition, and mechanical properties of thin films of transition metals diborides. Journal of Super hard Materials , 37 (6), 422-428. https://doi.org/10.3103/s1063457615060076

Шека, І. В., & Цівка, Є. С. (2021). Обґрунтування вуглепластику як інноваційного матеріалу для кріплення гірничих виробок вугільних шахт. Збірник Наукових Праць НГУ, 64 , 112–121. https://doi.org/10.33271/crpnmu/64.112

Гращенков, Д.В., & Чурсова, Л.В. (2012). Стратегия развития композиционных и функциональных материалов. Авиационные материалы и технологии , 231-242

Каблов, Е.Н. (2012). Стратегические направления развития материалов и технологий их переработки на период до 2030 года. Авиационные материалы и технологии , (5), 7-17

Amir, S.M.M., Sultan, M.T.H., Jawaid, M., Ariffin, A.H., Mohd, S., Salleh, K.A.M., Ishak, M.R., & Shah, A.U.M. (2019). Non destructive testing method for Kevlar and natural fiber and their hybrid composites. In Durability and Life Prediction in B iocomposites, Fibre-Reinforced Composites and Hybrid Composites . Elsevier. 367-388. https://doi.org/10.1016/b978-0-08-102290-0.00016-7

Kovalevska, I., Zhuravkov, M., Chervatiuk, V., Husiev, O., & Snihur, V. (2019). Generalization of trends in the influence of geomechanics factors on the choice of operation modes for the fastening system in the preparatory mineworkings. Mining of Mineral Deposits , 13 (3), 1-11. https://doi.org/10.33271/mining13.03.001

Bondarenko, V., Kovalevs'ka, I., Svystun, R., &Cherednichenko, Yu. (2013). Optimal parameters of wall bolts computation in the united bearing system of extraction workings frame-boltsupport. Annual Scientific-technical Collection – Mining of Mineral Deposits 2013 , 5-10. https://doi.org/10.1201/b16354-2

Khorolskyi, A., Hrinov, V., Mamaikin, O., & Demchenko, Yu. (2019). Models and methods to make decisions while mining productions cheduling. Mining of Mineral Deposits , 13 (4),53-62. https://doi.org/10.33271/mining13.04.053

Fomychov, V., Fomychova, L., Khorolskyi, A., Mamaikin, O. & Pochepov, V. (2020). Determining optimal border parameters to design a reused mineworking. ARPN Journal of Engineering and Applied Sciences , 15 (24), 3039-3049

Małkowski, P.,Niedbalski, Z.,Majcherczyk, T., & Bednarek, Ł. (2020). Underground monitoring as the best way of roadways support design validation in a long time period. Mining of Mineral Deposits , 14 (3), 1-14. https://doi.org/10.33271/mining14.03.001

Małkowski, P.,Niedbalski, Z.,&Balarabe, T. (2020). A statistical analysis of geomechanical data and its effect on rock mass numerical modeling: a casestudy. International Journal of Coal Science & Technological , 8 (4), 1-12. https://doi.org/10.1007/s40789-020-00369-2

Begalinov, A.,Almenov, T.,Zhanakova, R.,&Bektur, B. (2020). Analysis of the stress deformed state of rocks around the haulage roadway of the Beskempirfield (Kazakhstan). Mining of Mineral Deposits , 14 (3),28-36. https://doi.org/10.33271/mining14.03.028

Babets, D., Sdvyzhkova, O., Shashenko, O., Kravchenko, K., & Cabana, E.C. (2019). Implementation of probabilistic approach to rock mass strength estimation while excavating through fault zones. Mining of Mineral Deposits , 13 (4),72-83. https://doi.org/10.33271/mining13.04.072

Bondarenko, V., Kovalevska, I., Symanovych, G., Sotskov, V., &Barabash, M. (2018). Geomechanics of interference between the operation modes of mineworking support elements at their loading. Mining Science , (25),219-235. https://doi.org/10.5277/msc182515

Downloads

Published

2020-01-01

Issue

No. 68 (2022)

Section

Статті

License

All articles are published under the Creative Commons Attribution License (CC BY 4.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited. Authors retain copyright and grant the journal right of first publication.

Authors are permitted and encouraged to deposit the final published version of their article, or the Author's Accepted Manuscript (AAM), in institutional or subject-specific open-access repositories (including the university's own institutional repository, CORE, Zenodo, or Figshare), ensuring maximum visibility, accessibility, and impact of the publication.